contact us

contact-email
QQ--20190504180945_WPS--

DAMS Incorporated

We provide customers with quality products and provide high-quality services

看不清,请点击我!

If you would like to leave us a comment please go to contact us

contact-clo

What are the precautions for processing glass with edging machines and glass straight-line double edging machines

  • source:enkong
  • Time:06/12/2019

glass-edging-machine-news

In the processing of glass products, glass edging machine is one of the most important mechanical equipment in glass deep processing equipment. The main function of the glass straight- line double edging machine is to flatten the bottom edge of the glass or to grind it into a rounded edge.

Use edge grinding machine correctly and reasonably, not only ensures normal production, but also extends the life of the machine, resulting in increased production efficiency.

edge-grinding-machine-news

First, using the edging machine, we should pay attention to the following points:

 

First of all, for all kinds of newly purchased edger, be sure to read the instruction manual before use. After understanding the transmission principle of the machine, the role of various parts, and mastering the maintenance knowledge of the machine, the machine can be operated.

 

Next, the spindle has a great influence on the grinding quality of the glass, and the position of the spindle, moving clearance, etc. have been adjusted at the factory. When using, except for entering and leaving, the rest should not be moved, so as not to affect the grinding quality. In addition, the retracted position of the spindle is not easy to be too large, otherwise the waterproof sleeve is easily damaged, causing water leakage and easily burning the motor.

 

In attention, the sufficient cooling has a great influence on the grinding effect, that always check the cooling pipe for blockage. In particular, the pipeline of the straight-line edging machine is easily blocked by the bristles, and is not easily detected after the plugging, which may cause insufficient cooling to affect the quality of glass edging.

 

Second,  when using the Glass straight- line double edging machine, should pay attention to the following points:

 

Glass straight- line double edging machine is a higher-grade edging machine. It is best to fix two or three operations when using it to ensure correct operation. When its program appear error or failure, it is best to ask the original manufacturer to send someone to repair and debug. Under normal circumstances, do not dismantle it, so as to avoid disruption of the program.

 

Third, the use of glass straight-line double edging machine processing glass should pay attention to the following points:

 

  1.  Adjusting the width and thickness of the glass. Switch on the motor, be sure to wait for running idling for 2 minutes, and run normally to test.
  2.  Pay attention to observe the running condition of the whole machine during the trial grinding. If abnormal conditions are found, stop immediately, and exit the glass to eliminate the fault before starting.
  3.  Pay attention to the appearance, size, etc., and confirm that the first piece is qualified before mass production.
  4.  The grinding wheel of the machine can only be fed into the grinding wheel by 0.1mm, and it cannot be adjusted once.
  5.  If the glass waiting for grinding has entered the upper and lower pinch segments, it is found there is a misalignment or bursting of the glass, and it cannot be pulled directly but hand.
  6.  At the end of each shift, close the grinding head motor and then turn off the transfer, turn off the cooling water motor, remove the broken glass from the conveyor belt and its guide rails, feed rollers and other parts in time, and clean the sink and spout to prevent the glass. The powder does not clean up the sediment for a long time to block the cooling waterway system.
  7.  At least once a week, the cylinder needs to be lubricated and the manual pressure pump is used to pump the mechanical tubing system. The linear guide and the ball screws must be thoroughly lubricated and adjusted from the minimum width to the maximum width to prevent the memory of the guide rail and the screw from being damaged by grinding the small glass for a long time.
  8.  Lubricating the conveyor, please use the spray gun to add light engine oil under the timing belt.
  9.  Motor slides are lubricated once a week.

 

top